Screen Plants

Box-It™ 710 Recycler

CEC’s Box-It™ 710 is a rock, C & D, trash, gravel, soils, bank run, concrete demo, loam, bottom ash, gabion rock sorter. It can have top deck grizzly bars, punch plate, screen cloth or finger deck. The second deck is always screen cloth. Feed over the deck, course material comes over the screen and onto…

Continue reading

View the Box-It™ 710 Recycler

Boxer®

The Boxer is a grizzly top deck – screen second deck – fines scalper. The machine can be fed heavy rubble products and remove the dirt, sand and other fines. The 48” conveyor removes the fines and stacks them next to the Boxer. This machine can handle 100 – 450 TPH depending on the product…

Continue reading

View the Boxer®

Closed Circuit Five Product Track Plant

The CEC five product track crusher has a 26 x 42 or 30 x 42 jaw plant, track scalper, SC 300 cone plant and a 6 x 16 three deck screen. This plant can make (2) or (3) crushed products at a time plus a jaw scalped product and rejects natural fines and add natural…

Continue reading

View the Closed Circuit Five Product Track Plant

Closed Circuit Four Product Track Plant

Four product track plant has a 26 x 42 (30 x 42 also available) track mobile plant, a track scalper for excess fines, an SC 300 high speed cone and a 5 x 12 two deck finish screen. This plant is able to scalp out excess fines, crush high volume and make the most cubical…

Continue reading

View the Closed Circuit Four Product Track Plant

CEC Dual Impact Plant

The CEC dual impact plant is a very popular crushing plant for mobile operator and stationary plant. The plant crushes limestone with a 24″ minus feed, gravel with an 18″ minus feed, Basalt with a 24″ minus feed and concrete recycle with a 36″ x 24″ x 12″ feed. The reduction ratio is a maximum…

Continue reading

View the CEC Dual Impact Plant

Screening Plant – Feeder/Conveyor/Picking Station/Eddy Current

The CEC system pictured has a variable speed open throat feeder that allows maximum control of the in-feed product. This system is built for C & D material recovery. It will handle from 150 to 300 tons per hour depending on the C & D mixture. The open throat feed allows controlled feed and stratification…

Continue reading

View the Screening Plant – Feeder/Conveyor/Picking Station/Eddy Current

Incline Bare Screen

CEC builds screens at our plant in the state of Washington. The side walls are plasma cut in a submerged water bath cutting table. This reduces stress concentrations. The side walls are then moved to the machine shop for boring, drilling and counter sinking. This provides the mounting holes for the screen deck, screen mechanism,…

Continue reading

View the Incline Bare Screen

6 x 20 3 Deck Screen Plant

The 6 x 20 (3) deck screen is an 18° incline with hydraulic raise and lower on the screen. The screen has a 42” wide feed conveyor with wrap drive, a 48” wide under screen conveyor, front chutes, top deck return conveyor, “I” beam frame with jacking legs, access ladder, walkway, kick plates and hand…

Continue reading

View the 6 x 20 3 Deck Screen Plant

Track Scalper

The track screen scalper allows the course product to feed to the cone crusher and the excess fines to be removed. A percentage gate controls the fine flow.

View the Track Scalper

8 x 20 Three Deck Inline Screen

CEC has an 8 x 20 18° (3) deck incline screen. Pictured is a stock screen with a bolt together stand. This screen is spring-mounted, has blending discharge box, under screen hopper, access stairs, walkways with kick plates and railings. The screen has a 50 hp motor drive, 842 RPM shaft, .374”stroke and 170 mm…

Continue reading

View the 8 x 20 Three Deck Inline Screen

6 x 20 Screen Plant

The screen plant is a 6 x 20 (3) deck 18° incline screen with hydraulic set up. The plant and screen mate together at set up. The return product goes back to the impactor for resizing. This plant runs 400 plus tons per hour in limestone and 600 – 700 tons per hour in caliche…

Continue reading

View the 6 x 20 Screen Plant

Horizontal Bare Screen

CEC Horizontal Screens have a 45 degree stroke angle and a 5/8 stroke length. This allows lift of product for fine fall out and good product movement down the screen. The screens are mounted on Firestone rubber marshmallow vertical mounts and have bolt on corner rubber mounts for alignment. These corner mounts also control the…

Continue reading

View the Horizontal Bare Screen

Horizontal Dual Screen Plant

CEC builds dual horizontal screen plants in 6 x 16 and 6 x 20 (3) deck plants. The normal conveyor system of the dual plant is dual under conveyors on the primary screen. One conveyor can scalp and one feeds the product to the finish screen under conveyor. You can add a blending gate between…

Continue reading

View the Horizontal Dual Screen Plant

102 x 115 Track Impactor & Rambler®

CEC’s track mounted two unit crusher and rambler screens are built in several sizes. The unit pictured is the 102 x 115 track impactor and the 5 x 12 (2) deck Rambler® screen. The track units are conveyored so the screen tracks up to the impactor and the conveyors instantly match up. Set up is…

Continue reading

View the 102 x 115 Track Impactor & Rambler®

133 x 152 Portable Impactor

The 133 x 152 portable impact plant pictured was built for Martin Marietta in Texas.  They wanted high mobility, high production and self-contained operation. This crusher has a 48” wide apron feeder to a 4’ x 8’ grizzly bar scalper with a second deck.  A reject conveyor can remove the throughs when needed.  The impactor…

Continue reading

View the 133 x 152 Portable Impactor

133 x 152 Dual Impact Plant

CEC’s dual impactor plant is a very popular recycle plant with the concrete & asphalt recyclers. This plant has a 52” wide, 20’ long vibrating feeder with 6’ of grizzly bars and a second deck under grizzly reject screen for excess fines. The impactor is 60” wide and has a feed opening of 30” x…

Continue reading

View the 133 x 152 Dual Impact Plant